diff options
Diffstat (limited to 'test/ardmake/hardware/bootloaders/optiboot/Makefile')
| -rw-r--r-- | test/ardmake/hardware/bootloaders/optiboot/Makefile | 239 |
1 files changed, 239 insertions, 0 deletions
diff --git a/test/ardmake/hardware/bootloaders/optiboot/Makefile b/test/ardmake/hardware/bootloaders/optiboot/Makefile new file mode 100644 index 0000000..0fd6005 --- /dev/null +++ b/test/ardmake/hardware/bootloaders/optiboot/Makefile @@ -0,0 +1,239 @@ +# Makefile for ATmegaBOOT +# E.Lins, 18.7.2005 +# $Id$ +# +# Instructions +# +# To make bootloader .hex file: +# make diecimila +# make lilypad +# make ng +# etc... +# +# To burn bootloader .hex file: +# make diecimila_isp +# make lilypad_isp +# make ng_isp +# etc... + +# program name should not be changed... +PROGRAM = optiboot + +# enter the parameters for the avrdude isp tool +ISPTOOL = stk500v2 +ISPPORT = usb +ISPSPEED = -b 115200 + +MCU_TARGET = atmega168 +LDSECTION = --section-start=.text=0x3e00 + +# the efuse should really be 0xf8; since, however, only the lower +# three bits of that byte are used on the atmega168, avrdude gets +# confused if you specify 1's for the higher bits, see: +# http://tinker.it/now/2007/02/24/the-tale-of-avrdude-atmega168-and-extended-bits-fuses/ +# +# similarly, the lock bits should be 0xff instead of 0x3f (to +# unlock the bootloader section) and 0xcf instead of 0x0f (to +# lock it), but since the high two bits of the lock byte are +# unused, avrdude would get confused. + +ISPFUSES = avrdude -c $(ISPTOOL) -p $(MCU_TARGET) -P $(ISPPORT) $(ISPSPEED) \ +-e -u -U lock:w:0x3f:m -U efuse:w:0x$(EFUSE):m -U hfuse:w:0x$(HFUSE):m -U lfuse:w:0x$(LFUSE):m +ISPFLASH = avrdude -c $(ISPTOOL) -p $(MCU_TARGET) -P $(ISPPORT) $(ISPSPEED) \ +-U flash:w:$(PROGRAM)_$(TARGET).hex -U lock:w:0x0f:m + +STK500 = "C:\Program Files\Atmel\AVR Tools\STK500\Stk500.exe" +STK500-1 = $(STK500) -e -d$(MCU_TARGET) -pf -vf -if$(PROGRAM)_$(TARGET).hex \ +-lFF -LFF -f$(HFUSE)$(LFUSE) -EF8 -ms -q -cUSB -I200kHz -s -wt +STK500-2 = $(STK500) -d$(MCU_TARGET) -ms -q -lCF -LCF -cUSB -I200kHz -s -wt + +OBJ = $(PROGRAM).o +OPTIMIZE = -Os -fno-inline-small-functions -fno-split-wide-types -mshort-calls + +DEFS = +LIBS = + +CC = avr-gcc + +# Override is only needed by avr-lib build system. + +override CFLAGS = -g -Wall $(OPTIMIZE) -mmcu=$(MCU_TARGET) -DF_CPU=$(AVR_FREQ) $(DEFS) +override LDFLAGS = -Wl,$(LDSECTION) -Wl,--relax -nostartfiles + +OBJCOPY = avr-objcopy +OBJDUMP = avr-objdump + +# 20MHz clocked platforms +# +# These are capable of 230400 baud, or 115200 baud on PC (Arduino Avrdude issue) +# + +pro20: TARGET = pro_20mhz +pro20: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' +pro20: AVR_FREQ = 20000000L +pro20: $(PROGRAM)_pro_20mhz.hex +pro20: $(PROGRAM)_pro_20mhz.lst + +pro20_isp: pro20 +pro20_isp: TARGET = pro_20mhz +pro20_isp: HFUSE = DD # 2.7V brownout +pro20_isp: LFUSE = C6 # Full swing xtal (20MHz) 258CK/14CK+4.1ms +pro20_isp: EFUSE = 02 # 512 byte boot +pro20_isp: isp + +# 16MHz clocked platforms +# +# These are capable of 230400 baud, or 115200 baud on PC (Arduino Avrdude issue) +# + +pro16: TARGET = pro_16MHz +pro16: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' +pro16: AVR_FREQ = 16000000L +pro16: $(PROGRAM)_pro_16MHz.hex +pro16: $(PROGRAM)_pro_16MHz.lst + +pro16_isp: pro16 +pro16_isp: TARGET = pro_16MHz +pro16_isp: HFUSE = DD # 2.7V brownout +pro16_isp: LFUSE = C6 # Full swing xtal (20MHz) 258CK/14CK+4.1ms +pro16_isp: EFUSE = 02 # 512 byte boot +pro16_isp: isp + +# Diecimila and NG use identical bootloaders +# +diecimila: TARGET = diecimila +diecimila: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' +diecimila: AVR_FREQ = 16000000L +diecimila: $(PROGRAM)_diecimila.hex +diecimila: $(PROGRAM)_diecimila.lst + +diecimila_isp: diecimila +diecimila_isp: TARGET = diecimila +diecimila_isp: HFUSE = DD # 2.7V brownout +diecimila_isp: LFUSE = FF # Low power xtal (16MHz) 16KCK/14CK+65ms +diecimila_isp: EFUSE = 02 # 512 byte boot +diecimila_isp: isp + +atmega328: TARGET = atmega328 +atmega328: MCU_TARGET = atmega328p +atmega328: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' +atmega328: AVR_FREQ = 16000000L +atmega328: LDSECTION = --section-start=.text=0x7e00 +atmega328: $(PROGRAM)_atmega328.hex +atmega328: $(PROGRAM)_atmega328.lst + +atmega328_isp: atmega328 +atmega328_isp: TARGET = atmega328 +atmega328_isp: MCU_TARGET = atmega328p +atmega328_isp: HFUSE = DE # 512 byte boot +atmega328_isp: LFUSE = FF # Low power xtal (16MHz) 16KCK/14CK+65ms +atmega328_isp: EFUSE = 05 # 2.7V brownout +atmega328_isp: isp + +# 8MHz clocked platforms +# +# These are capable of 115200 baud +# + +lilypad: TARGET = lilypad +lilypad: CFLAGS += '-DLED_START_FLASHES=3' '-DSOFT_UART' '-DBAUD_RATE=115200' +lilypad: AVR_FREQ = 8000000L +lilypad: $(PROGRAM)_lilypad.hex +lilypad: $(PROGRAM)_lilypad.lst + +lilypad_isp: lilypad +lilypad_isp: TARGET = lilypad +lilypad_isp: HFUSE = DD # 2.7V brownout +lilypad_isp: LFUSE = E2 # Internal 8MHz osc (8MHz) Slow rising power +lilypad_isp: EFUSE = 02 # 512 byte boot +lilypad_isp: isp + +lilypad_resonator: TARGET = lilypad_resonator +lilypad_resonator: CFLAGS += '-DLED_START_FLASHES=3' '-DSOFT_UART' '-DBAUD_RATE=115200' +lilypad_resonator: AVR_FREQ = 8000000L +lilypad_resonator: $(PROGRAM)_lilypad_resonator.hex +lilypad_resonator: $(PROGRAM)_lilypad_resonator.lst + +lilypad_resonator_isp: lilypad_resonator +lilypad_resonator_isp: TARGET = lilypad_resonator +lilypad_resonator_isp: HFUSE = DD # 2.7V brownout +lilypad_resonator_isp: LFUSE = C6 # Full swing xtal (20MHz) 258CK/14CK+4.1ms +lilypad_resonator_isp: EFUSE = 02 # 512 byte boot +lilypad_resonator_isp: isp + +pro8: TARGET = pro_8MHz +pro8: CFLAGS += '-DLED_START_FLASHES=3' '-DSOFT_UART' '-DBAUD_RATE=115200' +pro8: AVR_FREQ = 8000000L +pro8: $(PROGRAM)_pro_8MHz.hex +pro8: $(PROGRAM)_pro_8MHz.lst + +pro8_isp: pro8 +pro8_isp: TARGET = pro_8MHz +pro8_isp: HFUSE = DD # 2.7V brownout +pro8_isp: LFUSE = C6 # Full swing xtal (20MHz) 258CK/14CK+4.1ms +pro8_isp: EFUSE = 02 # 512 byte boot +pro8_isp: isp + +atmega328_pro8: TARGET = atmega328_pro_8MHz +atmega328_pro8: MCU_TARGET = atmega328p +atmega328_pro8: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' +atmega328_pro8: AVR_FREQ = 8000000L +atmega328_pro8: LDSECTION = --section-start=.text=0x7e00 +atmega328_pro8: $(PROGRAM)_atmega328_pro_8MHz.hex +atmega328_pro8: $(PROGRAM)_atmega328_pro_8MHz.lst + +atmega328_pro8_isp: atmega328_pro8 +atmega328_pro8_isp: TARGET = atmega328_pro_8MHz +atmega328_pro8_isp: MCU_TARGET = atmega328p +atmega328_pro8_isp: HFUSE = DE # 512 byte boot +atmega328_pro8_isp: LFUSE = FF # Low power xtal (16MHz) 16KCK/14CK+65ms +atmega328_pro8_isp: EFUSE = 05 # 2.7V brownout +atmega328_pro8_isp: isp + +# 1MHz clocked platforms +# +# These are capable of 9600 baud +# + +luminet: TARGET = luminet +luminet: MCU_TARGET = attiny84 +luminet: CFLAGS += '-DLED_START_FLASHES=3' '-DSOFT_UART' '-DBAUD_RATE=9600' +luminet: CFLAGS += '-DVIRTUAL_BOOT_PARTITION' +luminet: AVR_FREQ = 1000000L +luminet: LDSECTION = --section-start=.text=0x1d00 +luminet: $(PROGRAM)_luminet.hex +luminet: $(PROGRAM)_luminet.lst + +luminet_isp: luminet +luminet_isp: TARGET = luminet +luminet_isp: MCU_TARGET = attiny84 +luminet_isp: HFUSE = DF # Brownout disabled +luminet_isp: LFUSE = 62 # 1MHz internal oscillator, slowly rising power +luminet_isp: EFUSE = FE # Self-programming enable +luminet_isp: isp + +isp: $(TARGET) + $(ISPFUSES) + $(ISPFLASH) + +isp-stk500: $(PROGRAM)_$(TARGET).hex + $(STK500-1) + $(STK500-2) + +%.elf: $(OBJ) + $(CC) $(CFLAGS) $(LDFLAGS) -o $@ $^ $(LIBS) + +clean: + rm -rf *.o *.elf *.lst *.map *.sym *.lss *.eep *.srec *.bin *.hex + +%.lst: %.elf + $(OBJDUMP) -h -S $< > $@ + +%.hex: %.elf + $(OBJCOPY) -j .text -j .data -O ihex $< $@ + +%.srec: %.elf + $(OBJCOPY) -j .text -j .data -O srec $< $@ + +%.bin: %.elf + $(OBJCOPY) -j .text -j .data -O binary $< $@ |