From 66dcf910bd4744d8ced56cb9586aa937a1a2d4c5 Mon Sep 17 00:00:00 2001 From: vg Date: Tue, 7 Jul 2020 16:24:01 +0200 Subject: first commit --- .../bootloaders/lilypad/LilyPadBOOT_168.hex | 117 +++ .../hardware/bootloaders/lilypad/src/ATmegaBOOT.c | 979 +++++++++++++++++++++ .../hardware/bootloaders/lilypad/src/Makefile | 84 ++ 3 files changed, 1180 insertions(+) create mode 100644 test/ardmake/hardware/bootloaders/lilypad/LilyPadBOOT_168.hex create mode 100644 test/ardmake/hardware/bootloaders/lilypad/src/ATmegaBOOT.c create mode 100644 test/ardmake/hardware/bootloaders/lilypad/src/Makefile (limited to 'test/ardmake/hardware/bootloaders/lilypad') diff --git a/test/ardmake/hardware/bootloaders/lilypad/LilyPadBOOT_168.hex b/test/ardmake/hardware/bootloaders/lilypad/LilyPadBOOT_168.hex new file mode 100644 index 0000000..aea378e --- /dev/null +++ b/test/ardmake/hardware/bootloaders/lilypad/LilyPadBOOT_168.hex @@ -0,0 +1,117 @@ +:103800000C94341C0C944F1C0C944F1C0C944F1CA7 +:103810000C944F1C0C944F1C0C944F1C0C944F1C7C +:103820000C944F1C0C944F1C0C944F1C0C944F1C6C +:103830000C944F1C0C944F1C0C944F1C0C944F1C5C +:103840000C944F1C0C944F1C0C944F1C0C944F1C4C +:103850000C944F1C0C944F1C0C944F1C0C944F1C3C +:103860000C944F1C0C944F1C11241FBECFEFD4E0BE +:10387000DEBFCDBF11E0A0E0B1E0E8E1FFE302C0B0 +:1038800005900D92A230B107D9F712E0A2E0B1E0A5 +:1038900001C01D92AD30B107E1F70C94311D0C94BD +:1038A000001CCF93DF93CDB7DEB724970FB6F89403 +:1038B000DEBF0FBECDBF382F882309F433E010924E +:1038C0000A02332309F44BC020E02D9A19821A8290 +:1038D0001B821C8289819A81AB81BC8180549F416B +:1038E000A040B040A0F489819A81AB81BC8101964F +:1038F000A11DB11D89839A83AB83BC8389819A8181 +:10390000AB81BC8180549F41A040B04060F32D98B2 +:1039100019821A821B821C8289819A81AB81BC81A7 +:1039200080549F41A040B040A0F489819A81AB812E +:10393000BC810196A11DB11D89839A83AB83BC8391 +:1039400089819A81AB81BC8180549F41A040B04065 +:1039500060F32F5F231708F4B8CF20930A02249650 +:103960000FB6F894DEBF0FBECDBFDF91CF910895A3 +:10397000EF92FF920F931F93EE24FF248701809113 +:10398000C00087FD17C00894E11CF11C011D111D2A +:1039900081E0E81689E0F8068DE3080780E0180763 +:1039A00070F3E0910201F091030109958091C0004C +:1039B00087FFE9CF8091C600992787FD90951F91D9 +:1039C0000F91FF90EF900895982F8091C00085FF90 +:1039D000FCCF9093C60008950E94B81C803271F00D +:1039E000809104018F5F80930401853009F0089570 +:1039F000E0910201F09103010995089584E10E948C +:103A0000E41C80E10E94E41C08951F93182F0E947B +:103A1000B81C803269F0809104018F5F80930401AB +:103A2000853079F4E0910201F0910301099509C014 +:103A300084E10E94E41C812F0E94E41C80E10E942A +:103A4000E41C1F910895282F882351F090E0809165 +:103A5000C00087FFFCCF8091C6009F5F2917B9F790 +:103A60000895CFEFD4E0DEBFCDBF000089E18093A1 +:103A7000C4001092C50088E18093C10086E0809365 +:103A8000C2005098589A259A83E00E94511C0E94C7 +:103A9000B81C8033B1F18133B9F1803409F454C0DA +:103AA000813409F45AC0823409F469C0853409F4B8 +:103AB0006CC0803531F1813521F1823511F18535C8 +:103AC00009F4B2C0863509F4BAC0843609F463C07B +:103AD000843709F4BBC0853709F40EC1863709F471 +:103AE0004AC0809104018F5F80930401853079F68C +:103AF000E0910201F091030109950E94B81C803306 +:103B000051F60E94EC1CC3CF0E94B81C803249F7CA +:103B100084E10E94E41C81E40E94E41C86E50E948A +:103B2000E41C82E50E94E41C80E20E94E41C89E41B +:103B30000E94E41C83E50E94E41C80E50E94E41CD2 +:103B400080E10E94E41CA3CF0E94B81C8638C8F212 +:103B50000E94B81C0E94EC1C9ACF0E94B81C8038AE +:103B600009F4F7C0813809F4F8C0823809F4F9C0C3 +:103B7000883909F4BDC080E00E94051D88CF84E12A +:103B80000E94231D0E94EC1C82CF85E00E94231D11 +:103B90000E94EC1C7CCF0E94B81C809309020E94FA +:103BA000B81C8093080280910C028E7F80930C02D7 +:103BB0000E94B81C853409F4C6C080910802909117 +:103BC0000902892B09F0ADC00E94B81C803209F0AF +:103BD00088CF80910C0280FFC8C08091080290912C +:103BE00009020097D1F02091060130910701E8E029 +:103BF000F1E0AC014E0F5F1FF999FECF32BD21BD40 +:103C0000819180BDFA9AF99A2F5F3F4F4E175F0757 +:103C100099F7309307012093060184E10E94E41C88 +:103C200080E10E94E41C33CF0E94B81C80930601FF +:103C30000E94B81C809307010E94EC1C28CF84E0EE +:103C40000E94231D80E00E94051D21CF0E94B81C08 +:103C5000809309020E94B81C809308020E94B81C3D +:103C6000853409F4F4C080910C028E7F80930C029D +:103C70008091060190910701880F991F9093070189 +:103C8000809306010E94B81C803209F000CF84E1C5 +:103C90000E94E41C2091080230910902211531058F +:103CA00019F1C0E0D0E0E0910601F09107018091A8 +:103CB0000C0280FFC4C0F999FECFF2BDE1BDF89AB5 +:103CC00080B50E94E41CE0910601F0910701319655 +:103CD000F0930701E0930601209108023091090258 +:103CE0002196C217D30718F380E10E94E41CCFCEBF +:103CF00083E00E94051DCBCE0E94B81C803209F0E3 +:103D0000F0CE84E10E94E41C8EE10E94E41C84E970 +:103D10000E94E41C86E00E94E41C80E10E94E41CF6 +:103D2000B6CEC0E0D0E008E011E00E94B81CF80177 +:103D300081938F0121968091080290910902C81702 +:103D4000D90798F341CF80910C02816080930C02D7 +:103D500034CF82E00E94051D9ACE81E00E94051DAD +:103D600096CE80E10E94051D92CE8091070187FDCD +:103D700080C010920B028091060190910701880F7C +:103D8000991F90930701809306018091080280FF9C +:103D900009C080910802909109020196909309024E +:103DA00080930802F894F999FECF1127E09106015B +:103DB000F0910701C8E0D1E08091080290910902DA +:103DC000103091F40091570001700130D9F303E0F5 +:103DD00000935700E8950091570001700130D9F326 +:103DE00001E100935700E895099019900091570060 +:103DF00001700130D9F301E000935700E895139565 +:103E0000103498F011270091570001700130D9F358 +:103E100005E000935700E8950091570001700130CC +:103E2000D9F301E100935700E8953296029709F023 +:103E3000C7CF103011F00296E5CF1124EECE81FFEE +:103E40000CC03196F0930701E093060149CF8091B1 +:103E50000C02816080930C0215CF84910E94E41CB7 +:103E60002091080230910902E0910601F0910701CA +:103E7000E8CF81E080930B027ECF0F931F930E94C7 +:103E8000B81C182F0E94E41C0E94B81C082F0E9426 +:103E9000E41C11362CF0175501363CF0075508C0CC +:103EA0001033D4F310530136CCF700330CF0005329 +:103EB0001295107F100F812F992787FD90951F91E4 +:103EC0000F9108951F93282F992787FD9095807F44 +:103ED00090709595879595958795959587959595E6 +:103EE00087958A304CF0982F995A822F8F708A309C +:103EF0004CF0182F195A08C0982F905D822F8F70A0 +:103F00008A30BCF7182F105D892F0E94E41C812F86 +:083F10000E94E41C1F910895BA +:023F1800800027 +:0400000300003800C1 +:00000001FF diff --git a/test/ardmake/hardware/bootloaders/lilypad/src/ATmegaBOOT.c b/test/ardmake/hardware/bootloaders/lilypad/src/ATmegaBOOT.c new file mode 100644 index 0000000..915bc57 --- /dev/null +++ b/test/ardmake/hardware/bootloaders/lilypad/src/ATmegaBOOT.c @@ -0,0 +1,979 @@ +/**********************************************************/ +/* Serial Bootloader for Atmel megaAVR Controllers */ +/* */ +/* tested with ATmega8, ATmega128 and ATmega168 */ +/* should work with other mega's, see code for details */ +/* */ +/* ATmegaBOOT.c */ +/* */ +/* 20070626: hacked for Arduino Diecimila (which auto- */ +/* resets when a USB connection is made to it) */ +/* by D. Mellis */ +/* 20060802: hacked for Arduino by D. Cuartielles */ +/* based on a previous hack by D. Mellis */ +/* and D. Cuartielles */ +/* */ +/* Monitor and debug functions were added to the original */ +/* code by Dr. Erik Lins, chip45.com. (See below) */ +/* */ +/* Thanks to Karl Pitrich for fixing a bootloader pin */ +/* problem and more informative LED blinking! */ +/* */ +/* For the latest version see: */ +/* http://www.chip45.com/ */ +/* */ +/* ------------------------------------------------------ */ +/* */ +/* based on stk500boot.c */ +/* Copyright (c) 2003, Jason P. Kyle */ +/* All rights reserved. */ +/* see avr1.org for original file and information */ +/* */ +/* This program is free software; you can redistribute it */ +/* and/or modify it under the terms of the GNU General */ +/* Public License as published by the Free Software */ +/* Foundation; either version 2 of the License, or */ +/* (at your option) any later version. */ +/* */ +/* This program is distributed in the hope that it will */ +/* be useful, but WITHOUT ANY WARRANTY; without even the */ +/* implied warranty of MERCHANTABILITY or FITNESS FOR A */ +/* PARTICULAR PURPOSE. See the GNU General Public */ +/* License for more details. */ +/* */ +/* You should have received a copy of the GNU General */ +/* Public License along with this program; if not, write */ +/* to the Free Software Foundation, Inc., */ +/* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +/* */ +/* Licence can be viewed at */ +/* http://www.fsf.org/licenses/gpl.txt */ +/* */ +/* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */ +/* m8515,m8535. ATmega161 has a very small boot block so */ +/* isn't supported. */ +/* */ +/* Tested with m168 */ +/**********************************************************/ + +/* $Id$ */ + + +/* some includes */ +#include +#include +#include +#include +#include + + +/* the current avr-libc eeprom functions do not support the ATmega168 */ +/* own eeprom write/read functions are used instead */ +#ifndef __AVR_ATmega168__ +#include +#endif + +/* Use the F_CPU defined in Makefile */ + +/* 20060803: hacked by DojoCorp */ +/* 20070626: hacked by David A. Mellis to decrease waiting time for auto-reset */ +/* set the waiting time for the bootloader */ +/* get this from the Makefile instead */ +/* #define MAX_TIME_COUNT (F_CPU>>4) */ + +/* 20070707: hacked by David A. Mellis - after this many errors give up and launch application */ +#define MAX_ERROR_COUNT 5 + +/* set the UART baud rate */ +/* 20060803: hacked by DojoCorp */ +//#define BAUD_RATE 115200 +#define BAUD_RATE 19200 + + +/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */ +/* never allow AVR Studio to do an update !!!! */ +#define HW_VER 0x02 +#define SW_MAJOR 0x01 +#define SW_MINOR 0x10 + + +/* Adjust to suit whatever pin your hardware uses to enter the bootloader */ +/* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */ +/* BL0... means UART0, BL1... means UART1 */ +#ifdef __AVR_ATmega128__ +#define BL_DDR DDRF +#define BL_PORT PORTF +#define BL_PIN PINF +#define BL0 PINF7 +#define BL1 PINF6 +#else +/* other ATmegas have only one UART, so only one pin is defined to enter bootloader */ +#define BL_DDR DDRD +#define BL_PORT PORTD +#define BL_PIN PIND +#define BL PIND6 +#endif + + +/* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */ +/* if monitor functions are included, LED goes on after monitor was entered */ +#ifdef __AVR_ATmega128__ +/* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128) */ +#define LED_DDR DDRB +#define LED_PORT PORTB +#define LED_PIN PINB +#define LED PINB7 +#else +/* Onboard LED is connected to pin PB2 (e.g. Crumb8, Crumb168) */ +#define LED_DDR DDRB +#define LED_PORT PORTB +#define LED_PIN PINB +/* 20060803: hacked by DojoCorp, LED pin is B5 in Arduino */ +/* #define LED PINB2 */ +#define LED PINB5 +#endif + + +/* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */ +#ifdef __AVR_ATmega128__ +#define MONITOR +#endif + + +/* define various device id's */ +/* manufacturer byte is always the same */ +#define SIG1 0x1E // Yep, Atmel is the only manufacturer of AVR micros. Single source :( + +#if defined __AVR_ATmega128__ +#define SIG2 0x97 +#define SIG3 0x02 +#define PAGE_SIZE 0x80U //128 words + +#elif defined __AVR_ATmega64__ +#define SIG2 0x96 +#define SIG3 0x02 +#define PAGE_SIZE 0x80U //128 words + +#elif defined __AVR_ATmega32__ +#define SIG2 0x95 +#define SIG3 0x02 +#define PAGE_SIZE 0x40U //64 words + +#elif defined __AVR_ATmega16__ +#define SIG2 0x94 +#define SIG3 0x03 +#define PAGE_SIZE 0x40U //64 words + +#elif defined __AVR_ATmega8__ +#define SIG2 0x93 +#define SIG3 0x07 +#define PAGE_SIZE 0x20U //32 words + +#elif defined __AVR_ATmega88__ +#define SIG2 0x93 +#define SIG3 0x0a +#define PAGE_SIZE 0x20U //32 words + +#elif defined __AVR_ATmega168__ +#define SIG2 0x94 +#define SIG3 0x06 +#define PAGE_SIZE 0x40U //64 words + +#elif defined __AVR_ATmega162__ +#define SIG2 0x94 +#define SIG3 0x04 +#define PAGE_SIZE 0x40U //64 words + +#elif defined __AVR_ATmega163__ +#define SIG2 0x94 +#define SIG3 0x02 +#define PAGE_SIZE 0x40U //64 words + +#elif defined __AVR_ATmega169__ +#define SIG2 0x94 +#define SIG3 0x05 +#define PAGE_SIZE 0x40U //64 words + +#elif defined __AVR_ATmega8515__ +#define SIG2 0x93 +#define SIG3 0x06 +#define PAGE_SIZE 0x20U //32 words + +#elif defined __AVR_ATmega8535__ +#define SIG2 0x93 +#define SIG3 0x08 +#define PAGE_SIZE 0x20U //32 words +#endif + + +/* function prototypes */ +void putch(char); +char getch(void); +void getNch(uint8_t); +void byte_response(uint8_t); +void nothing_response(void); +char gethex(void); +void puthex(char); +void flash_led(uint8_t); + +/* some variables */ +union address_union { + uint16_t word; + uint8_t byte[2]; +} address; + +union length_union { + uint16_t word; + uint8_t byte[2]; +} length; + +struct flags_struct { + unsigned eeprom : 1; + unsigned rampz : 1; +} flags; + +uint8_t buff[256]; +uint8_t address_high; + +uint8_t pagesz=0x80; + +uint8_t i; +uint8_t bootuart = 0; + +uint8_t error_count = 0; + +void (*app_start)(void) = 0x0000; + + +/* main program starts here */ +int main(void) +{ + uint8_t ch,ch2; + uint16_t w; + + asm volatile("nop\n\t"); + + /* set pin direction for bootloader pin and enable pullup */ + /* for ATmega128, two pins need to be initialized */ +#ifdef __AVR_ATmega128__ + BL_DDR &= ~_BV(BL0); + BL_DDR &= ~_BV(BL1); + BL_PORT |= _BV(BL0); + BL_PORT |= _BV(BL1); +#else + /* We run the bootloader regardless of the state of this pin. Thus, don't + put it in a different state than the other pins. --DAM, 070709 + BL_DDR &= ~_BV(BL); + BL_PORT |= _BV(BL); + */ +#endif + + +#ifdef __AVR_ATmega128__ + /* check which UART should be used for booting */ + if(bit_is_clear(BL_PIN, BL0)) { + bootuart = 1; + } + else if(bit_is_clear(BL_PIN, BL1)) { + bootuart = 2; + } +#endif + + /* check if flash is programmed already, if not start bootloader anyway */ + if(pgm_read_byte_near(0x0000) != 0xFF) { + +#ifdef __AVR_ATmega128__ + /* no UART was selected, start application */ + if(!bootuart) { + app_start(); + } +#else + /* check if bootloader pin is set low */ + /* we don't start this part neither for the m8, nor m168 */ + //if(bit_is_set(BL_PIN, BL)) { + // app_start(); + // } +#endif + } + +#ifdef __AVR_ATmega128__ + /* no bootuart was selected, default to uart 0 */ + if(!bootuart) { + bootuart = 1; + } +#endif + + + /* initialize UART(s) depending on CPU defined */ +#ifdef __AVR_ATmega128__ + if(bootuart == 1) { + UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); + UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8; + UCSR0A = 0x00; + UCSR0C = 0x06; + UCSR0B = _BV(TXEN0)|_BV(RXEN0); + } + if(bootuart == 2) { + UBRR1L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); + UBRR1H = (F_CPU/(BAUD_RATE*16L)-1) >> 8; + UCSR1A = 0x00; + UCSR1C = 0x06; + UCSR1B = _BV(TXEN1)|_BV(RXEN1); + } +#elif defined __AVR_ATmega163__ + UBRR = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); + UBRRHI = (F_CPU/(BAUD_RATE*16L)-1) >> 8; + UCSRA = 0x00; + UCSRB = _BV(TXEN)|_BV(RXEN); +#elif defined __AVR_ATmega168__ + UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); + UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8; + UCSR0B = (1<>8; // set baud rate + UBRRL = (((F_CPU/BAUD_RATE)/16)-1); + UCSRB = (1<> 8; + UCSRA = 0x00; + UCSRC = 0x06; + UCSRB = _BV(TXEN)|_BV(RXEN); +#endif + + /* set LED pin as output */ + LED_DDR |= _BV(LED); + + + /* flash onboard LED to signal entering of bootloader */ +#ifdef __AVR_ATmega128__ + // 4x for UART0, 5x for UART1 + flash_led(NUM_LED_FLASHES + bootuart); +#else + flash_led(NUM_LED_FLASHES); +#endif + + /* 20050803: by DojoCorp, this is one of the parts provoking the + system to stop listening, cancelled from the original */ + //putch('\0'); + + + /* forever loop */ + for (;;) { + + /* get character from UART */ + ch = getch(); + + /* A bunch of if...else if... gives smaller code than switch...case ! */ + + /* Hello is anyone home ? */ + if(ch=='0') { + nothing_response(); + } + + + /* Request programmer ID */ + /* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry */ + /* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares. */ + else if(ch=='1') { + if (getch() == ' ') { + putch(0x14); + putch('A'); + putch('V'); + putch('R'); + putch(' '); + putch('I'); + putch('S'); + putch('P'); + putch(0x10); + } else { + if (++error_count == MAX_ERROR_COUNT) + app_start(); + } + } + + + /* AVR ISP/STK500 board commands DON'T CARE so default nothing_response */ + else if(ch=='@') { + ch2 = getch(); + if (ch2>0x85) getch(); + nothing_response(); + } + + + /* AVR ISP/STK500 board requests */ + else if(ch=='A') { + ch2 = getch(); + if(ch2==0x80) byte_response(HW_VER); // Hardware version + else if(ch2==0x81) byte_response(SW_MAJOR); // Software major version + else if(ch2==0x82) byte_response(SW_MINOR); // Software minor version + else if(ch2==0x98) byte_response(0x03); // Unknown but seems to be required by avr studio 3.56 + else byte_response(0x00); // Covers various unnecessary responses we don't care about + } + + + /* Device Parameters DON'T CARE, DEVICE IS FIXED */ + else if(ch=='B') { + getNch(20); + nothing_response(); + } + + + /* Parallel programming stuff DON'T CARE */ + else if(ch=='E') { + getNch(5); + nothing_response(); + } + + + /* Enter programming mode */ + else if(ch=='P') { + nothing_response(); + } + + + /* Leave programming mode */ + else if(ch=='Q') { + nothing_response(); + } + + + /* Erase device, don't care as we will erase one page at a time anyway. */ + else if(ch=='R') { + nothing_response(); + } + + + /* Set address, little endian. EEPROM in bytes, FLASH in words */ + /* Perhaps extra address bytes may be added in future to support > 128kB FLASH. */ + /* This might explain why little endian was used here, big endian used everywhere else. */ + else if(ch=='U') { + address.byte[0] = getch(); + address.byte[1] = getch(); + nothing_response(); + } + + + /* Universal SPI programming command, disabled. Would be used for fuses and lock bits. */ + else if(ch=='V') { + getNch(4); + byte_response(0x00); + } + + + /* Write memory, length is big endian and is in bytes */ + else if(ch=='d') { + length.byte[1] = getch(); + length.byte[0] = getch(); + flags.eeprom = 0; + if (getch() == 'E') flags.eeprom = 1; + for (w=0;w127) address_high = 0x01; //Only possible with m128, m256 will need 3rd address byte. FIXME + else address_high = 0x00; +#ifdef __AVR_ATmega128__ + RAMPZ = address_high; +#endif + address.word = address.word << 1; //address * 2 -> byte location + /* if ((length.byte[0] & 0x01) == 0x01) length.word++; //Even up an odd number of bytes */ + if ((length.byte[0] & 0x01)) length.word++; //Even up an odd number of bytes + cli(); //Disable interrupts, just to be sure + // HACKME: EEPE used to be EEWE + while(bit_is_set(EECR,EEPE)); //Wait for previous EEPROM writes to complete + asm volatile( + "clr r17 \n\t" //page_word_count + "lds r30,address \n\t" //Address of FLASH location (in bytes) + "lds r31,address+1 \n\t" + "ldi r28,lo8(buff) \n\t" //Start of buffer array in RAM + "ldi r29,hi8(buff) \n\t" + "lds r24,length \n\t" //Length of data to be written (in bytes) + "lds r25,length+1 \n\t" + "length_loop: \n\t" //Main loop, repeat for number of words in block + "cpi r17,0x00 \n\t" //If page_word_count=0 then erase page + "brne no_page_erase \n\t" + "wait_spm1: \n\t" + "lds r16,%0 \n\t" //Wait for previous spm to complete + "andi r16,1 \n\t" + "cpi r16,1 \n\t" + "breq wait_spm1 \n\t" + "ldi r16,0x03 \n\t" //Erase page pointed to by Z + "sts %0,r16 \n\t" + "spm \n\t" +#ifdef __AVR_ATmega163__ + ".word 0xFFFF \n\t" + "nop \n\t" +#endif + "wait_spm2: \n\t" + "lds r16,%0 \n\t" //Wait for previous spm to complete + "andi r16,1 \n\t" + "cpi r16,1 \n\t" + "breq wait_spm2 \n\t" + + "ldi r16,0x11 \n\t" //Re-enable RWW section + "sts %0,r16 \n\t" + "spm \n\t" +#ifdef __AVR_ATmega163__ + ".word 0xFFFF \n\t" + "nop \n\t" +#endif + "no_page_erase: \n\t" + "ld r0,Y+ \n\t" //Write 2 bytes into page buffer + "ld r1,Y+ \n\t" + + "wait_spm3: \n\t" + "lds r16,%0 \n\t" //Wait for previous spm to complete + "andi r16,1 \n\t" + "cpi r16,1 \n\t" + "breq wait_spm3 \n\t" + "ldi r16,0x01 \n\t" //Load r0,r1 into FLASH page buffer + "sts %0,r16 \n\t" + "spm \n\t" + + "inc r17 \n\t" //page_word_count++ + "cpi r17,%1 \n\t" + "brlo same_page \n\t" //Still same page in FLASH + "write_page: \n\t" + "clr r17 \n\t" //New page, write current one first + "wait_spm4: \n\t" + "lds r16,%0 \n\t" //Wait for previous spm to complete + "andi r16,1 \n\t" + "cpi r16,1 \n\t" + "breq wait_spm4 \n\t" +#ifdef __AVR_ATmega163__ + "andi r30,0x80 \n\t" // m163 requires Z6:Z1 to be zero during page write +#endif + "ldi r16,0x05 \n\t" //Write page pointed to by Z + "sts %0,r16 \n\t" + "spm \n\t" +#ifdef __AVR_ATmega163__ + ".word 0xFFFF \n\t" + "nop \n\t" + "ori r30,0x7E \n\t" // recover Z6:Z1 state after page write (had to be zero during write) +#endif + "wait_spm5: \n\t" + "lds r16,%0 \n\t" //Wait for previous spm to complete + "andi r16,1 \n\t" + "cpi r16,1 \n\t" + "breq wait_spm5 \n\t" + "ldi r16,0x11 \n\t" //Re-enable RWW section + "sts %0,r16 \n\t" + "spm \n\t" +#ifdef __AVR_ATmega163__ + ".word 0xFFFF \n\t" + "nop \n\t" +#endif + "same_page: \n\t" + "adiw r30,2 \n\t" //Next word in FLASH + "sbiw r24,2 \n\t" //length-2 + "breq final_write \n\t" //Finished + "rjmp length_loop \n\t" + "final_write: \n\t" + "cpi r17,0 \n\t" + "breq block_done \n\t" + "adiw r24,2 \n\t" //length+2, fool above check on length after short page write + "rjmp write_page \n\t" + "block_done: \n\t" + "clr __zero_reg__ \n\t" //restore zero register +#if defined __AVR_ATmega168__ + : "=m" (SPMCSR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31" +#else + : "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31" +#endif + ); + /* Should really add a wait for RWW section to be enabled, don't actually need it since we never */ + /* exit the bootloader without a power cycle anyhow */ + } + putch(0x14); + putch(0x10); + } else { + if (++error_count == MAX_ERROR_COUNT) + app_start(); + } + } + + + /* Read memory block mode, length is big endian. */ + else if(ch=='t') { + length.byte[1] = getch(); + length.byte[0] = getch(); +#if defined __AVR_ATmega128__ + if (address.word>0x7FFF) flags.rampz = 1; // No go with m256, FIXME + else flags.rampz = 0; +#endif + if (getch() == 'E') flags.eeprom = 1; + else { + flags.eeprom = 0; + address.word = address.word << 1; // address * 2 -> byte location + } + if (getch() == ' ') { // Command terminator + putch(0x14); + for (w=0;w < length.word;w++) { // Can handle odd and even lengths okay + if (flags.eeprom) { // Byte access EEPROM read +#ifdef __AVR_ATmega168__ + while(EECR & (1<= 'a') { + ah = ah - 'a' + 0x0a; + } else if(ah >= '0') { + ah -= '0'; + } + if(al >= 'a') { + al = al - 'a' + 0x0a; + } else if(al >= '0') { + al -= '0'; + } + return (ah << 4) + al; +} + + +void puthex(char ch) { + char ah,al; + + ah = (ch & 0xf0) >> 4; + if(ah >= 0x0a) { + ah = ah - 0x0a + 'a'; + } else { + ah += '0'; + } + al = (ch & 0x0f); + if(al >= 0x0a) { + al = al - 0x0a + 'a'; + } else { + al += '0'; + } + putch(ah); + putch(al); +} + + +void putch(char ch) +{ +#ifdef __AVR_ATmega128__ + if(bootuart == 1) { + while (!(UCSR0A & _BV(UDRE0))); + UDR0 = ch; + } + else if (bootuart == 2) { + while (!(UCSR1A & _BV(UDRE1))); + UDR1 = ch; + } +#elif defined __AVR_ATmega168__ + while (!(UCSR0A & _BV(UDRE0))); + UDR0 = ch; +#else + /* m8,16,32,169,8515,8535,163 */ + while (!(UCSRA & _BV(UDRE))); + UDR = ch; +#endif +} + + +char getch(void) +{ +#ifdef __AVR_ATmega128__ + if(bootuart == 1) { + while(!(UCSR0A & _BV(RXC0))); + return UDR0; + } + else if(bootuart == 2) { + while(!(UCSR1A & _BV(RXC1))); + return UDR1; + } + return 0; +#elif defined __AVR_ATmega168__ + uint32_t count = 0; + while(!(UCSR0A & _BV(RXC0))){ + /* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/ + /* HACKME:: here is a good place to count times*/ + count++; + if (count > MAX_TIME_COUNT) + app_start(); + } + return UDR0; +#else + /* m8,16,32,169,8515,8535,163 */ + uint32_t count = 0; + while(!(UCSRA & _BV(RXC))){ + /* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/ + /* HACKME:: here is a good place to count times*/ + count++; + if (count > MAX_TIME_COUNT) + app_start(); + } + return UDR; +#endif +} + + +void getNch(uint8_t count) +{ + uint8_t i; + for(i=0;i $@ + +%.srec: %.elf + $(OBJCOPY) -j .text -j .data -O srec $< $@ + +%.bin: %.elf + $(OBJCOPY) -j .text -j .data -O binary $< $@ + +clean: + rm -rf *.o *.elf *.lst *.map *.sym *.lss *.eep *.srec *.bin *.hex + +install: + avrdude -p m168 -c stk500v2 -P /dev/cu.USA19H1b1P1.1 -e -u -U lock:w:0x3f:m -U efuse:w:0x00:m -U hfuse:w:0xdd:m -U lfuse:w:0xe2:m + avrdude -p m168 -c stk500v2 -P /dev/cu.USA19H1b1P1.1 -e -u -U flash:w:ATmegaBOOT_168.hex -U lock:w:0x0f:m -- cgit v1.2.3