aboutsummaryrefslogtreecommitdiffstats
path: root/contrib/preauth-harness
blob: 0bd0d842079c2fb4c0fca494cfd018a71802df6d (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
#!/usr/bin/perl

BEGIN { $SIG{'__WARN__'} = sub {};};

$hostname = "criens.u-psud.fr";
$username = "p99dreyf";
$passwd = "xxxxxxxx";
$command = "exec ~/bin/imapd";

use Net::Telnet ();
$host = new Net::Telnet (Timeout => 10,
                         Port => 23,
                         Prompt => '/p99dreyf>\s?$/',
                         Cmd_remove_mode => 1);

$host->option_accept(Dont => &Net::Telnet::TELOPT_ECHO,
                     Wont => &Net::Telnet::TELOPT_ECHO);
                     open (FILE,">log");
$host->dump_log("log2");
$host->input_log("log3");
## Issue some commands.
$host->open($hostname);
#$host->login($username, $passwd);
$host->waitfor('/login:\s?$/');
$host->print("$username");
$host->waitfor('/Password:\s?$/');
$host->print("$passwd");
$host->waitfor('/p99dreyf>\s?$/');

$host->print("$command");
$strip=1;
while ($strip) {
        $greeting=$host->getline();
   if ($greeting=~/^\* PREAUTH.*$/) { print "$greeting"; $strip=0;};
}
    do {
      do {
        $cmd=<STDIN>;
        chop $cmd;
      } while ($cmd !~/[A-Za-z0-9]/);
      $host->print("$cmd");
      print FILE ">>$cmd<<\n";
      do {
        $line=$host->getline();
        chop($line);
        print "$line\n";
        print FILE "<<$line<<\n";
      } while (($line!~/^[A-Za-z0-9]+ (OK|BAD|Expunge).*$/) &&
                ($line!~/^\* BAD.*$/));
      print FILE "--next cmd\n";
    } while ($line!~/^[A-Za-z0-9]+ OK LOGOUT.*$/);

exit;
is that local alias expansion according to /etc/aliases won't get done if we fall back to it. 2.2 Advanced options Specifying --with-kerberos=DIR or --with-kerberos5=DIR will tell the fetchmail build process to look in DIR for Kerberos support. Configure normally looks in /usr/kerberos and /usr/athena; if you specify this option with an argument it will look in DIR first. Unfortunately, there doesn't seem to be good standardization of where Kerberos lives. If your configuration doesn't match one of the four that fetchmail's configure.in knows about, you may find you have to hand-hack the Makefile a bit. You may also want to hand-hack the Makefile if you're writing a custom or bleeding-edge resolver library. In that case you will probably want to add -lresolv or whatever to the definition of LOADLIBS. It is also possible to explicitly condition out the support for POP3, IMAP, and ETRN (with configure arguments of --disable-POP3, --disable-IMAP, and --disable-ETRN respectively). 3. BUILD Run make This should compile fetchmail for your system. If fetchmail fails to build properly, see the FAQ section B on build-time problems. 4. INSTALL Lastly, become root and run make install This will install fetchmail. By default, fetchmail will be installed in /usr/local/bin, with the man page in /usr/local/man/man1. You can use the configure options --bindir and --mandir to change these. If you are tight on disk space, you can run instead make install-strip NOTE: If you are using an MTA other than sendmail (such as qmail, exim, or smail), see the FAQ (section T) for discussion of any special configuration steps that may be necessary. 5. SET UP A RUN CONTROL FILE See the man page for a description of how to configure your individual preferences. If you're upgrading from popclient, see question F4 in the FAQ file. 6. TEST I strongly recommend that your first fetchmail run use the -v, -a and -k options, in case there is something not quite right with your server, your local delivery configuration or your port 25 listener. Also, beware of aliases that direct your local mail back to the server host! This software is known to work with the qpop/popper series of freeware POP3 servers; also with the IMAP2bis and IMAP4 servers that are distributed with Pine from the University of Washington; also with the Cyrus IMAP server from CMU. This covers all the servers commonly hosted on Linux and *BSD systems. It also works with the IMAP service of Microsoft Exchange, despite the fact that Microsoft Exchange is extremely broken (returns incorrect message lengths in LIST responses). See the FAQ, section S, for detailed advice on running with various servers. 7. REPORTING BUGS You should read the FAQ file question G3 before reporting a bug. 8. USE IT Once you've verified your configuration, you can start fetchmail to run in background and forget about it. Enjoy! END of text file INSTALL